Linux.com

Home Linux Community Community Blogs Personal Configure Arch Linux - rc.config

Configure Arch Linux - rc.config


In my installations of Arch Linux, I found that file the most complicated to configure.
So I'm sending mine to serve as the basis for those trying.

#
# /etc/rc.conf - Main Configuration for Arch Linux
#

#
# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
#
LOCALE="pt_BR.utf8"
HARDWARECLOCK="localtime"
TIMEZONE="America/Sao_Paulo"
KEYMAP="br-abnt2"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"

#
# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# Scan hardware and load required modules at bootup
MOD_AUTOLOAD="yes"
# Module Blacklist - modules in this list will never be loaded by udev
MOD_BLACKLIST=()
#
# Modules to load at boot-up (in this order)
#   - prefix a module with a ! to blacklist it
#
MODULES=()
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"

#
# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
HOSTNAME="Arch"
#
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available
# interfaces.
#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
#   - prefix an entry in INTERFACES with a ! to disable it
#   - no hyphens in your interface names - Bash doesn't like it
#
# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
#
eth0="dhcp"
INTERFACES=(lo eth0)
#
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
#   - prefix an entry in ROUTES with a ! to disable it
#
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
#
# Enable these network profiles at boot-up.  These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
#   - set to 'menu' to present a menu during boot-up (dialog package required)
#   - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network-profiles
#
#NET_PROFILES=(main)

#
# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
#   - prefix a daemon with a ! to disable it
#   - prefix a daemon with a @ to start it up in the background
#
DAEMONS=(syslog-ng dbus hal network netfs crond alsa gdm fam vboxdrv)


# End of file

 

 

 

Comments

Subscribe to Comments Feed

Upcoming Linux Foundation Courses

  1. LFD331 Developing Linux Device Drivers
    25 Aug » 29 Aug - Virtual
    Details
  2. LFD411 Embedded Linux Development
    25 Aug » 29 Aug - Santa Clara, CA
    Details
  3. LFS422 High Availability Linux Architecture
    08 Sep » 11 Sep - Raleigh, NC
    Details

View All Upcoming Courses


Who we are ?

The Linux Foundation is a non-profit consortium dedicated to the growth of Linux.

More About the foundation...

Frequent Questions

Join / Linux Training / Board