Linux.com

IO-Perf-HOWTO

I/O Performance HOWTO

Sharon Snider

v1.1, 05/2002

Revision History
Revision v1.1 2002-05-01 Revised by: sds
Updated technical information and links.
Revision v1.0 2002-04-01 Revised by: sds
Wrote and converted to DocBook XML.

This HOWTO covers information on available patches for the 2.4 kernel that can improve the I/O performance of your Linux™ operating system.


1. Distribution Policy

The I/O Performance-HOWTO is copyrighted © 2002, by IBM Corporation

Permission is granted to copy, distribute, and/or modify this document under the terms of the GNU Free Documentation License, Version 1.1 or any later version published by the Free Software Foundation with no Invariant Sections, no Front-Cover text, and no Back-Cover text. A copy of the license can be found at http://www.gnu.org/licenses/fdl.txt.


2. Introduction

This HOWTO provides information on improving the input/output (I/O) performance of the Linux operating system for the 2.4 kernel. Additional patches will be added as they become available.

Please send any comments, or contributions via e-mail to This e-mail address is being protected from spambots. You need JavaScript enabled to view it .


3. Avoiding Bounce Buffers

This section provides information on applying and using the bounce buffer patch on the Linux 2.4 kernel. The bounce buffer patch, written by Jens Axboe, enables device drivers that support direct memory access (DMA) I/O to high-address physical memory to avoid bounce buffers.

This document provides a brief overview on memory and addressing in the Linux kernel, followed by information on why and how to make use of the bounce buffer patch.


3.3. Locating the Patch

The latest version of the bounce buffer patch is block-highmem-all-18b.bz2, and it is available from Andrea Arcangeli's -aa series kernels at http://kernel.org/pub/linux/kernel/people/andrea/kernels/v2.4/.


3.3.1. Configuring the Linux Kernel to Avoid Bounce Buffers

This section includes information on configuring the Linux kernel to avoid bounce buffers. The Linux Kernel-HOWTO at http://www.linuxdoc.org/HOWTO/Kernel-HOWTO.html explains the process of re-compiling the Linux kernel.

The following kernel configuration options are required to enable the bounce buffer patch:

Development Code - To enable the configurator to display the High I/O Support option, select the Code maturity level options category and specify "y" to Prompt for development and/or incomplete code/drivers.

High Memory Support - To enable support for physical memory that is greater than 1 GB, select the Processor type and features category, and select a value from the High Memory Support option.

High Memory I/O Support - To enable DMA I/O to physical addresses greater than 1 GB, select the Processor type and features category, and enter "y" to the HIGHMEM I/O support option. This configuration option is a new option introduced by the bounce buffer patch.


3.4. Modifying Your Device Driver to Avoid Bounce Buffers

If your device drivers are not listed above in the Enabled Device Drivers section, and the device is capable of high-memory DMA I/O, you can modify your device driver to make use of the bounce buffer patch as follows. More information on rebuilding a Linux device driver is available at http://www.xml.com/ldd/chapter/book/index.html.

  1. A.) For SCSI Adapter Drivers: set the highmem_io bit in the Scsi_Host_Template structure.

    B.) For IDE Adapter Drivers: set the highmembit in the ide_hwif_t structure.

  2. Call pci_set_dma_mask(struct pci_dev *pdev, dma_addr_t mask) to specify the address bits that the device can successfully use on DMA operations.

    If DMA I/O can be supported with the specified mask, pci_set_dma_mask() will set pdev->dma_mask and return 0. For SCSI or IDE, the mask value will also be passed by the mid-level drivers to blk_queue_bounce_limit(request_queue_t *q, u64 dma_addr) so that bounce buffers are not created for memory directly addressable by the device. Drivers other than SCSI or IDE must call blk_queue_bounce_limit() directly.

  3. Use pci_map_page(dev, page, offset, size, direction), instead of pci_map_single(dev, address, size, direction) to map a memory region so that it is accessible by the peripheral device. pci_map_page() supports both high and low memory.

    The address parameter for pci_map_single() correlates to the page and offset parameters for pci_map_page(). Use the virt_to_page() macro to convert an address to a page and offset. The virt_to_page() macro is defined by including pci.h. For example:

    void *address;
    
    struct page *page;
    
    unsigned long offset;
    
    page = virt_to_page(address);
    
    offset = (unsigned long) address & ~PAGE_MASK;
    

    Call pci_unmap_page() after the DMA I/O transfer is complete to remove the mapping established by pci_map_page().

    Note

    pci_map_single() is implemented using virt_to_bus(). virt_to_bus() handles low memory addresses only. Drivers supporting high memory should no longer call virt_to_bus() or bus_to_virt().

  4. If your driver calls pci_map_sg() to map a scatter-gather DMA operation, your driver should set the page and offset fields instead of the address field of the scatterlist structure. Refer to step 3 for converting an address to a page and offset.

    Note

    If your driver is already using the PCI DMA API, continue to use pci_map_page() or pci_map_sg() as appropriate. However, do not use the address field of the scatterlist structure.


4. Raw I/O Variable-Size Optimization Patch

This section provides information on the raw I/O variable-size optimization patch for the Linux 2.4 kernel written by Badari Pulavarty. This patch is also known as the RAW VARY or PAGESIZE_io patch.

The raw I/O variable-size patch changes the block size used for raw I/O from hardsect_size (normally 512 bytes) to 4 kilobytes (K). The patch improves I/O throughput and CPU utilization by reducing the number of buffer heads needed for raw I/O operations.


4.1. Locating the Patch

You can download the patch from one of the following locations:


5. I/O Request Lock Patch

This section provides information on the I/O request lock patch, also known as the scsi concurrent queuing patch (sior1), written by Johnathan Lahr.

The I/O request lock patch improves SCSI I/O performance on Linux 2.4 multi-processor systems by providing concurrent I/O request queuing. There are significant I/O performance and CPU utilization improvements possible by enabling multi-processors to concurrently drive multiple block devices.

Before the patch is applied block I/O requests are queued one at a time holding the global spin lock, io_request_lock. Once the patch is applied, SCSI requests are queued while holding the lock specific to the queue associated with the request. Requests that are made to different devices are queued concurrently, and requests that are made to the same device are queued serially.


5.1. Locating the Patch

You can download the I/O request patch from Sourceforge at http://sourceforge.net/projects/lse/io. The latest version is sior1-v1.2416. Patches that enable concurrent queuing for specific drivers are also available at SourceForge. The patch for the Emulex SCSI/FC is lpfc_sior1-v0.249 and the patch for Adaptec SCSI is aic_sior1-v0.249.


6. Additional Resources

The following list of Web sites provides additional information on modifying device drivers and configuring the Linux kernel.

 

Comments

Subscribe to Comments Feed

Who we are ?

The Linux Foundation is a non-profit consortium dedicated to the growth of Linux.

More About the foundation...

Frequent Questions

Join / Linux Training / Board