Manpage of WRITE

WRITE

Section: Linux Programmer's Manual (2)
Updated: 2016-03-15
Index
 

NAME

write - write to a file descriptor  

SYNOPSIS

#include <unistd.h>

ssize_t write(int fd, const void *buf, size_t count); 

DESCRIPTION

write() writes up to countbytes from the buffer pointed bufto the file referred to by the file descriptor fd.

The number of bytes written may be less than countif, for example, there is insufficient space on the underlying physical medium, or the RLIMIT_FSIZEresource limit is encountered (see setrlimit(2)), or the call was interrupted by a signal handler after having written less than countbytes. (See also pipe(7).)

For a seekable file (i.e., one to which lseek(2) may be applied, for example, a regular file) writing takes place at the file offset, and the file offset is incremented by the number of bytes actually written. If the file was open(2)ed with O_APPEND, the file offset is first set to the end of the file before writing. The adjustment of the file offset and the write operation are performed as an atomic step.

POSIX requires that a read(2) which can be proved to occur after a write() has returned returns the new data. Note that not all filesystems are POSIX conforming.  

RETURN VALUE

On success, the number of bytes written is returned (zero indicates nothing was written). It is not an error if this number is smaller than the number of bytes requested; this may happen for example because the disk device was filled. See also NOTES.

On error, -1 is returned, and errno is set appropriately.

If count is zero and fdrefers to a regular file, then write() may return a failure status if one of the errors below is detected. If no errors are detected, or error detection is not performed, 0 will be returned without causing any other effect. If count is zero and fdrefers to a file other than a regular file, the results are not specified.  

ERRORS

EAGAIN
The file descriptor fdrefers to a file other than a socket and has been marked nonblocking (O_NONBLOCK), and the write would block. See open(2) for further details on the O_NONBLOCKflag.
EAGAIN or EWOULDBLOCK
The file descriptor fdrefers to a socket and has been marked nonblocking (O_NONBLOCK), and the write would block. POSIX.1-2001 allows either error to be returned for this case, and does not require these constants to have the same value, so a portable application should check for both possibilities.
EBADF
fdis not a valid file descriptor or is not open for writing.
EDESTADDRREQ
fdrefers to a datagram socket for which a peer address has not been set using connect(2).
EDQUOT
The user's quota of disk blocks on the filesystem containing the file referred to by fdhas been exhausted.
EFAULT
bufis outside your accessible address space.
EFBIG
An attempt was made to write a file that exceeds the implementation-defined maximum file size or the process's file size limit, or to write at a position past the maximum allowed offset.
EINTR
The call was interrupted by a signal before any data was written; see signal(7).
EINVAL
fdis attached to an object which is unsuitable for writing; or the file was opened with the O_DIRECTflag, and either the address specified in buf, the value specified in count, or the file offset is not suitably aligned.
EIO
A low-level I/O error occurred while modifying the inode.
ENOSPC
The device containing the file referred to by fdhas no room for the data.
EPERM
The operation was prevented by a file seal; see fcntl(2).
EPIPE
fdis connected to a pipe or socket whose reading end is closed. When this happens the writing process will also receive a SIGPIPEsignal. (Thus, the write return value is seen only if the program catches, blocks or ignores this signal.)

Other errors may occur, depending on the object connected to fd.  

CONFORMING TO

SVr4, 4.3BSD, POSIX.1-2001.

Under SVr4 a write may be interrupted and return EINTRat any point, not just before any data is written.  

NOTES

The types size_tand ssize_tare, respectively, unsigned and signed integer data types specified by POSIX.1.

A successful return from write() does not make any guarantee that data has been committed to disk. In fact, on some buggy implementations, it does not even guarantee that space has successfully been reserved for the data. The only way to be sure is to call fsync(2) after you are done writing all your data.

If a write() is interrupted by a signal handler before any bytes are written, then the call fails with the error EINTR; if it is interrupted after at least one byte has been written, the call succeeds, and returns the number of bytes written.

On Linux, write() (and similar system calls) will transfer at most 0x7ffff000 (2,147,479,552) bytes, returning the number of bytes actually transferred. (This is true on both 32-bit and 64-bit systems.)  

BUGS

According to POSIX.1-2008/SUSv4 Section XSI 2.9.7 ("Thread Interactions with Regular File Operations"):

All of the following functions shall be atomic with respect to each other in the effects specified in POSIX.1-2008 when they operate on regular files or symbolic links: ...

Among the APIs subsequently listed are write() and writev(2). And among the effects that should be atomic across threads (and processes) are updates of the file offset. However, on Linux before version 3.14, this was not the case: if two processes that share an open file description (see open(2)) perform a write() (or writev(2)) at the same time, then the I/O operations were not atomic with respect updating the file offset, with the result that the blocks of data output by the two processes might (incorrectly) overlap. This problem was fixed in Linux 3.14.  

SEE ALSO

close(2), fcntl(2), fsync(2), ioctl(2), lseek(2), open(2), pwrite(2), read(2), select(2), writev(2), fwrite(3)


 

Index

NAME
SYNOPSIS
DESCRIPTION
RETURN VALUE
ERRORS
CONFORMING TO
NOTES
BUGS
SEE ALSO

This document was created by man2html, using the manual pages.
Time: 22:27:43 GMT, June 20, 2016