Manpage of NUMA
NUMASection: Linux Programmer's Manual (7)
NAMEnuma - overview of Non-Uniform Memory Architecture
DESCRIPTIONNon-Uniform Memory Access (NUMA) refers to multiprocessor systems whose memory is divided into multiple memory nodes. The access time of a memory node depends on the relative locations of the accessing CPU and the accessed node. (This contrasts with a symmetric multiprocessor system, where the access time for all of the memory is the same for all CPUs.) Normally, each CPU on a NUMA system has a local memory node whose can be accessed faster than the memory in the node local to another CPU or the memory on a bus shared by all CPUs.
NUMA system callsThe Linux kernel implements the following NUMA-related system calls: get_mempolicy(2), mbind(2), migrate_pages(2), move_pages(2), and set_mempolicy(2). However, applications should normally use the interface provided by libnuma; see "Library Support" below.
/proc/[number]/numa_maps (since Linux 2.6.14)This file displays information about a process's NUMA memory policy and allocation.
Each line contains information about a memory range used by the process, displaying---among other information---the effective memory policy for that memory range and on which nodes the pages have been allocated.
numa_mapsis a read-only file. When /proc/<pid>/numa_mapsis read, the kernel will scan the virtual address space of the process and report how memory is used. One line is displayed for each unique memory range of the process.
The first field of each line shows the starting address of the memory range. This field allows a correlation with theof the /proc/<pid>/mapsfile, which contains the end address of the range and other information, such as the access permissions and sharing.
The second field shows the memory policy currently in effect for the memory range. Note that the effective policy is not necessarily the policy installed by the process for that memory range. Specifically, if the process installed a "default" policy for that range, the effective policy for that range will be the process policy, which may or may not be "default".
The rest of the line contains information about the pages allocated in the memory range, as follows:
- The number of pages allocated on <node>. <nr_pages>includes only pages currently mapped by the process. Page migration and memory reclaim may have temporarily unmapped pages associated with this memory range. These pages may show up again only after the process has attempted to reference them. If the memory range represents a shared memory area or file mapping, other processes may currently have additional pages mapped in a corresponding memory range.
- The file backing the memory range. If the file is mapped as private, write accesses may have generated COW (Copy-On-Write) pages in this memory range. These pages are displayed as anonymous pages.
- Memory range is used for the heap.
- Memory range is used for the stack.
- Huge memory range. The page counts shown are huge pages and not regular sized pages.
- The number of anonymous page in the range.
- Number of dirty pages.
- Total number of mapped pages, if different from dirtyand anonpages.
- Maximum mapcount (number of processes mapping a single page) encountered during the scan. This may be used as an indicator of the degree of sharing occurring in a given memory range.
- Number of pages that have an associated entry on a swap device.
- The number of pages on the active list. This field is shown only if different from the number of pages in this range. This means that some inactive pages exist in the memory range that may be removed from memory by the swapper soon.
- Number of pages that are currently being written out to disk.
CONFORMING TONo standards govern NUMA interfaces.
NOTESThe Linux NUMA system calls and /procinterface are available only if the kernel was configured and built with the CONFIG_NUMAoption.
Library supportLink with -lnumato get the system call definitions. libnumaand the required <numaif.h>header are available in the numactlpackage.
However, applications should not use these system calls directly. Instead, the higher level interface provided by the numa(3) functions in the numactlpackage is recommended. The numactlpackage is available at The package is also included in some Linux distributions. Some distributions include the development library and header in the separate numactl-develpackage.
SEE ALSOget_mempolicy(2), mbind(2), move_pages(2), set_mempolicy(2), numa(3), cpuset(7), numactl(8)
- CONFORMING TO
- SEE ALSO
This document was created by man2html, using the manual pages.
Time: 16:30:28 GMT, December 12, 2016 Click Here!